Terminal Table
The terminal table lists every terminal-category symbol (the 端子 (Terminal) category, such as an XT strip) together with where its wires go, which makes it the main deliverable for on-site wiring and wire checking. The whole tab is a Pro feature: in the free version it shows a panel reading “端子表为 Pro 功能” (the terminal table is a Pro feature) with a 了解 Pro… (Learn about Pro…) button.
What the table contains
The columns are, in order:
| Column | Where the value comes from | Editable here? |
|---|---|---|
| 端子排 (Terminal strip) | The properties panel under 端子 ▸ 端子排 (Terminal ▸ Terminal strip), or edited directly in the table | Yes |
| 端子号 (Terminal number) | The properties panel under 端子 ▸ 端子号 (Terminal ▸ Terminal number), or written by 自动编号 (auto numbering) | Yes |
| 图纸 (Sheet) / 分区 (Zone) | The page the terminal is on and its 50 mm zone number (for example B3) | No |
| 上端线号 (Upper wire no.) / 下端线号 (Lower wire no.) | The wire numbers of the wires attached to the terminal's two pins; empty when none can be resolved | No (edit the wire or its number) |
| 去向 (Destination) | Inferred from the other end of the wire, in the form “设备代号 引脚名” (device tag, then pin name); a wire that runs into an off-page connector is shown as “中断点 网络名” (off-page connector + network name); when the device at the other end has no tag it falls back to “符号名称 引脚名” (symbol name, then pin name). If the upper and lower results are the same they are shown once, otherwise they are joined with “/” | No |
| 备注 (Notes) | The properties panel under 端子 ▸ 备注 (Terminal ▸ Notes) | Yes |
| 定位 (Locate) | A button (hover tip “在图纸中定位该端子” (locate this terminal in the drawing)) | — |
Clicking 定位 (Locate) switches to the sheet that holds the terminal, selects it and closes the report window. The footer reads 共 N 个端子 · M 个端子排 (N terminals in total · M terminal strips) and adds the hint “端子排、端子号和备注可直接在表格中编辑” (terminal strip, terminal number and notes can be edited right in the table). When the table is empty it shows 暂无端子 (no terminals yet) and the hint “从符号库放置“端子 (XT)”并连接导线后,端子表自动生成。” (Once you place “端子 (XT)” from the symbol library and connect wires, the terminal table is generated automatically.)
Tip
Only terminal-category symbols appear in the table. The decision is based on the category in the symbol definition
(terminals), not on whether the component's name contains the word “端子”. If you need the terminal table to cover other devices,
your only options today are to place terminal-category symbols or to write a text annotation.
Auto numbering
Next to the “自动编号” (Auto Numbering) tab in the toolbar, the 编号规则… (Numbering Rules…) button opens the panel (unavailable while the table is empty). The panel is titled 端子自动编号 (Terminal Auto Numbering) and contains:
| Field | Description |
|---|---|
| 前缀 (Prefix) | Prefix for the terminal number, placeholder example 如 X; leave it empty for pure numbers. |
| 起始号 (Start number) | The number given to the first terminal. |
| 步长 (Step) | The increment; minimum 1. |
| 每个端子排独立编号 (Number each terminal strip separately) | When ticked, every strip counts from the start again; when unticked, numbering runs continuously across the whole project. |
The panel explains itself with “按端子排、排序号及图面位置依次编号,并写入端子号” (number in order of terminal strip, sort number and drawing position, then write the terminal numbers) — that is, the order first follows the strip a terminal belongs to and the sort number carried by the symbol, and then the position on the sheet. The result is written straight into each terminal's 端子号 (Terminal number) field, so you can still edit individual terminals by hand afterwards; the next auto numbering simply overwrites those edits. Undo rolls back the whole batch.
How it relates to wire numbers
- The 上端/下端线号 (upper/lower wire number) columns come from wire numbers: if nothing
is numbered yet, run 图纸 ▸ 线号 ▸ 全部重新编号 (Drawing ▸ Wire Numbers ▸ Renumber All) first, or type a company code such
as
1Udirectly in the wire properties. - Terminals that leave the enclosure are expressed with off-page connectors: the destination column then shows “中断点 网络名” (off-page connector + network name), and on site you follow that name to the identically named target terminal in the other cabinet.
- Exporting with 导出 CSV (Export CSV) (free) or 导出 Excel (Export Excel) (Pro) writes exactly
the columns you see on screen; the default file name looks like
未命名项目-端子表.csv.