Wiring
The wire tool connects two points with an orthogonal polyline: it only runs horizontal and vertical segments, and the corners are generated by the program. The snap radius is fixed at 6 mm, and endpoints automatically align to pins, 接点 (Junctions), or existing wires.
Drawing a Wire
- Click 导线 (Wire) in the toolbar, or press W on the canvas (tooltip: "从元件引脚或已有导线按下并拖拽,松开完成,Esc 取消" — press on a component pin or an existing wire and drag; release to finish; Esc cancels).
- Press at the start point: near a pin, a snap marker lights up and the point locks onto the pin; the same happens near an existing wire or junction.
- Drag to the end point and release to complete the wire. Pressing Esc midway cancels the operation and creates no object.
- With 吸附到网格 (Snap to Grid) enabled (on by default), endpoints that land on nothing align to the grid; turn it off and endpoints can sit at any coordinate.
What Counts as "Connected"
| Situation | Result |
|---|---|
| An endpoint lands within 6 mm of a pin | The endpoint snaps and binds to that pin; it follows when the component moves. |
| An endpoint lands on another wire | That wire is split into two segments, a solid junction is generated automatically, and the three segments merge into one potential network. |
| An endpoint lands on an existing junction | It joins that junction, merging the networks the same way. |
| Two wires merely cross | They do not connect. A crossing implies no electrical relationship — this is the default convention of schematics. |
| A crossing that should connect | Use the junction tool (press J): click on the crossing of two or more wires to place a junction, and every wire passing through it merges into one network. |
Tip
The junction is the only way to make crossings connect. Its diameter is fixed at 1.6 mm, and junctions at the same position are deduplicated (regardless of layer). Deleting a junction only breaks the connection; the wires stay. So after you delete a T-shaped junction, the wires that were joined instantly split into separate networks, and wire numbers and cross-references are recalculated accordingly.
Wire Properties
Select a wire and the 导线属性 (Wire Properties) panel on the right shows, in order:
| Group | Contents and Values |
|---|---|
| 图层 (Layer) | Dropdown to switch the owning layer; see Layers. |
| 线号 (Wire Number) | The 编号 (Number) field accepts manual input; 锁定线号(重编号时跳过) (Lock Wire Number — skip when renumbering) is a Pro feature — in the free version the checkbox cannot be enabled: it appears checked and dimmed, and clicking it shows the tooltip "线号锁定为 Pro 功能" (Wire-number locking is a Pro feature). The wire's number and lock state are always kept in sync, so the checkbox state reflects the wire's actual state. |
| 导线颜色 (Wire Color) | 默认(黑) (Default, black), 红色 (Red), 黑色 (Black), 蓝色 (Blue), 绿色 (Green), 黄色 (Yellow). Purely for visual distinction on the sheet; they play no part in electrical calculations. Both Default and Black draw black; they differ only in whether the color follows the theme on export. |
| 导线线宽 (Wire Width) | 细线(0.7 mm) (Thin), 中粗线(1.0 mm) (Medium), 标准(1.4 mm) (Standard), 粗线(2.0 mm) (Thick); the default is Standard. The values come from the ISO 6960 / GB/T 17450 preferred width series and are rendered as real millimeter widths, so in PDF/PNG/SVG/DXF/VSDX the stroke weights match the actual print size, independent of zoom. |
| 路径 (Path) | Shows 拐点 N 个 (N bends) and, in blue, 手动控制点 N 个 (N manual control points), lists each point's coordinates (manual points are marked with ●), and offers 恢复自动布线 (Restore Auto Routing). See Wire Paths. |
| 连接 (Connections) | Per end: the start/end connected pin and connected junction, or, when unbound, 起点悬空/终点悬空 (start/end dangling) highlighted in orange. |
Editing and Deleting
- Drag a wire's endpoint to change the connection: drop it on another pin/wire/junction to rebind, and dragging it away from the connected point detaches it (it becomes dangling).
- Right-click a wire and choose 删除 (Delete), or select it and press ⌫; undo entries are named 绘制导线 (Draw Wire)/删除 (Delete) and so on.
- Wire number, color, and width are all set per wire — there is no "batch-edit all similar objects". With a multi-selection the properties panel only supports 分配到图层… (Assign to Layer…).
- When a component is deleted, its wires' endpoints detach and dangle; the wire bodies themselves are not deleted.
After Drawing
Networks are computed automatically from the connectivity of "pins + wires + junctions": within one network, wire numbers, potential names, and terminal-table destinations all change together. Crossing wires without a junction are two different networks — a fact reflected in both Electrical Rules Check and Wire Numbers.