Symbol Library
The symbol library follows GB/T 4728 and IEC 60617 and contains 64 standard symbols in 17 categories; the free version gives you 17 basic symbols, and the rest carry a PRO badge. A free Generic Component (in the General category) covers components the library does not have.
The Symbol Library tab in the sidebar
- Switch the top of the sidebar to 符号库 (Symbol Library).
- The search field's placeholder text is 名称 / 拼音 / 编号 (Name / Pinyin / Code): you can type
“交流接触器” (AC contactor), pinyin initials such as
jjc, or the symbol code. - Results are grouped into collapsible categories, with the category count to the right of each group title; above the list it says 找到 N 个符号 (N symbols found) when searching, or 共 N 个符号 · M 个 Pro (N symbols total · M Pro) when browsing.
- Click a symbol row to select it, and the tool automatically switches back to 选择 (Select); then click once on the canvas and the component lands at the click point (aligned to the grid when snapping is on). The selection stays active, so you can keep clicking to place several on the same page.
- Right-click a symbol row for 加入收藏 (Add to Favorites) / 取消收藏 (Remove from Favorites); favorited symbols are grouped above the list for quick access to everyday parts.
- In the free version Pro symbols are still listed, but tagged with PRO and the hint “Pro 符号,解锁后可放置” (_a Pro symbol; place it after unlocking_); clicking to place one opens the Pro explanation. The bottom of the list also has an 解锁完整符号库 (Unlock the Full Symbol Library) button.
Categories
| Category | Typical symbols |
|---|---|
| General (通用) | Generic Component — a box placeholder for parts the library lacks, with pins you can add, remove, rename and move to another side |
| Circuit breakers / air switches, fuses (断路器/空开、熔断器) | Miniature circuit breaker, moulded-case circuit breaker, fuse switch-disconnector |
| Switches, contactors, relays, thermal overload relays (开关、接触器、继电器、热继电器) | Changeover switch, push-button switch, AC contactor coils and contacts, intermediate relay, thermal relay and its normally-closed contact |
| Buttons, indicator lamps, motors (按钮、指示灯、电机) | Normally-open/normally-closed buttons, indicator lamp, three-phase motor and windings |
| Transformers, meters, power supplies (变压器、仪表、电源) | Control transformer, voltmeter/ammeter, switch-mode power supply (AC/DC) |
| Passive components (无源元件) | Resistor, capacitor, inductor, diode |
| Terminals, ground/potential (端子、接地/电位) | Terminal block XT, protective earth PE, shield/functional ground |
| PLC terminals (PLC端子) | Digital input/output terminals |
| Cross-page interruption points (跨页中断点) | Interruption Point Source and Interruption Point Target (the identically named toolbar tools can place them directly too) |
What you can change after placing
- Position and orientation: enter X and Y in the inspector, or click 旋转 90° (Rotate 90°); the shortcut is ⌘R. Rotation only steps in 90° increments — there are no arbitrary angles.
- No mirroring, no scaling: symbols are drawn exactly as defined; they cannot be flipped or enlarged, and stroke sizes cannot be changed either.
- Component attributes: the attributes carried by the symbol definition (for example pole count, rated current) are displayed read-only, as a reference for filling in the BOM's model/rating.
- Pins (引脚): each pin's name, type (power input / power output / signal input / signal output / passive / ground), and the potential group it belongs to (L1/L2/L3/N/PEN/DC24V/0V/SG, etc.) are listed; ground-type pins are merged into the PE network.
- Layer (图层): with a single selection, a drop-down changes the layer directly; with multiple objects, use 分配到图层… (Assign to Layer…) in the “N Objects Selected” panel — see Layers.
Tip
Deleting a component takes its connections with it. When a component is deleted, the wire endpoints connected to its pins come loose (the wires themselves are kept, but their ends become floating), so after deleting, run 图纸 ▸ 电气检查 (Sheet ▸ Electrical Check) to find floating pins; ⌘Z undoes the whole operation.
Want to place your own symbols?
Version 1.0 has no custom symbol editor: you can neither draw new symbols nor import external symbol files. The 自定义符号 (Custom Symbols) entry in the Pro feature list is only a placeholder for now. If you need a different graphic, use an imported DXF underlay as a reference or add notes with text annotations, and feed the requirement back to the developer to extend the built-in library.